To
configure a reader of main CD-ROM in unit.
You have two readers of CD-ROM and you do not know which
is the Master or the slave (Slavic), either to start again
with a CD-ROM or to solve a breakdown. It is enough to
open the UC and to look at behind units. A small rider
is located at it, it is enough to place it into Slavic
so that the reader is in unit slave and conversely for
the other. The position is indicated beside the rider.
hight
of Page
To
make conceal the mother chart.
To decontaminate the voice which announces with starting
that the mother chart functions well it is necessary to
pass by Bios. Choose the Advanced mitre, select the line
Bios Features and made Entrer. Select the line Speech
Post to defer and press on the Entrer key. Notch the Disabled
value then on Entrer and the F10 key. Type on Y and Entry
to start again in silence.
hight
of Page
The
switch of food does not function well.
Maintaining all towers ATX have two switches, one in front
of, the other behind. That of front can be programmed
like putting in day before or on/off. Go in Bios and go
in small Power Management Setup to carry out the adjustment.
hight
of Page
Hard
disk with half usable.
You have change the hard disk by another of greater capacity,
but the PC sees of them only the 32 or the first 80 Go.
It is because of your Bios which cannot read some more.
Go then on the sites of the manufacturers of the hard
disks, they will give you a program which can stage to
that. Another possibility, upgrader Bios, but there, it
is necessary to be really qualified. Download the update
of Bios which you will put on the diskette of starting.
Start again with the diskette and carry out the utility
for the update.
hight
of Page
The
posting of the message.
Ntldr not found. For Windows 2000, this message appears
with starting, and it is impossible to start Windows.
It is that the Ntldr file is essential for starting and
it has faded being. It is then necessary to start with
the diskette of starting and to choose Installation of
Windows 2000 and to insert the CD-ROM. When the menu appears,
choose emergency Repare and Repair.
hight
of Page
Message
Hardware Disk Failure...
That wants to say that the hard disk is not recognized
by Bios. It should well be checked that the tablecloth
is well connected (the red edge must be more close to
the electric cable) like all the cables. Try to start
with the diskette of starting and type C: , if that still
does not go, use Fdisk/mbr striking. Otherwise, I advise
you to shut off the current and to go to see a pro to
avoid losing all the data and repairing the disc.
hight
of Page
Nothing
ignites.
You in vain tried to start the PC but nothing ignites
and there is no noise. That must come from the alimentation.
Either it is the fuse to be removed, or straightforwardly
the power supply unit. Pay great attention to change the
fuse, you are extremely likely to electrocute you. Make
do it by a specialist.
hight
of Page
The
peripheral is not recognized.
The peripheral should well be connected: open the CPU
and check that all the contacts are well put and that
the reader is well alimented.
Look at the small rider which is with the back of the
peripheral. If it is alone, put in master. So on the other
hand two peripherals are connected on same tablecloth
(style CD-ROM and CD-RW), put that which is fastest on
master and the other on slave.
hight
of Page
Recognition
of a peripheral under XP.
To make recognize an external modem under Windows XP,
it is necessary that this one is lit before starting.
Once started, made a right click on Working station select
Propertys, in the Material mitre click on Gestionnaire
of peripherals. Click on an entry of the list, in small
Action To seek the modifications on the material.
hight
of Page
Windows
starts and the screen becomes black.
A parameter in properties of posting has changed being.
It is necessary to start in mode without failure. Make
a right click on the Desk and choose Property in Parameters,
you choose a minimal definition. You can start again,
made the same thing that presently to make your adjustments
but indicate that you refuse to start again. If the screen
becomes black, it is enough for you to support on Echap.
hight
of Page
The
reader of CD-ROM idles.
You find that your reader of CD-ROM is enough to see very
slow.... Then it is necessary to open the tour and to
change the connection of the reader. It should be connected
directly to the mother chart and not to the same wire
tablecloth as the hard disk. For that, it is necessary
go in the Control panel, in Systeme then in the manager
mitre of peripherals. In the CD-ROM category, you choose
yours and go in Propertys, here you notch box DMA. Start
again the PC.
hight
of Page
Windows
starts in mode without failure.
If the PC starts in mode without failure, it is very often
with a problem involved in the graphics board. Either
it is not managed any more by the pilot good, or a conflict
with place with a new peripheral. To then configure the
graphics board in standard mode VGA and start again.
hight
of Page
The
PC ignites because of a telephone call.
That can make smile but certain Bios were programmed so
that the PC ignites automatically when it detects a signal
on one of its ports series. Thus when it is in day before
and that a person telephones to you and if it is equipped
with a modem connected to the line of the telephone, he
ignites. To regulate this function it will be necessary
to pass by Bios. Go in small Power Management Setup (of
the program of the setup of Bios) and go in function IRQ
Wake Up Events or Modem uses IRQ.
hight
of Page
Windows
page does not start and transmits messages of alarms.
The PC starts but not Windows, in addition to that you
have messages of alarm.
All depends on the posted messages. If you have Non system
disk, that wants to say that you surely forgot to remove
the diskette in the reader. It is necessary to remove
it and support on Enter.
The message Disk error means, that after having to install
a hard disk, that you forgot to activate the principal
partition. It is then necessary to start the PC in Back
with the diskette of starting. There it is necessary to
type Fdisk and choose Activate the principal partition.
The message Disk error can as mean as the hard disk is
faded. Always in Back mode, type Fdisk/mbr. If that does
not go, check that the connections of the disc are well
fixed. If nothing made there, the hard disk must be really
damaged.
hight
of Page
When
Windows stops, the PC is blocked.
You want to extinguish the PC, Windows stops and the message
to have patience does not cease remaining with the screen.
Either rebooter is needed then, or to shut off the current.
That must come from a pilot of one of the peripheral which
frees.
It is then necessary to go in msconfig (To start/Execute
and to type msconfig) to notch the Desactivate box the
fast stop in advanced the Options mitre. If nothing made
there, it will then be necessary to update the pilots
of the peripherals.
hight
of Page
The
central processing unit makes noise.
If the central processing unit makes an abnormally strong
noise, open to check that the ventilators are well fixed.
If despite everything the continuous noise, it will be
necessary to change one, see all and check them fixings
of all the peripherals. Do not be afraid, it is rather
easy to make...
hight
of Page
Windows 
![[]](http://m3.moostik.net/img/?pseudo=borisette&cpt=Accueil&data=site&option=invisible)